| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
... as its help message says in menuconfig.
Signed-off-by: Alexey Neyman <stilor@att.net>
|
|
In that case, CT_GetCustom just creates a symlink to the original.
In that case, 'cp -a <path> .' gives an error and 'cp -a <path> <newdir>'
creates <newdir> as a symlink (which will then run the build inside
the shared directory, .build/src/<package>).
Signed-off-by: Alexey Neyman <stilor@att.net>
|
|
The referenced commit replaced 'make' with '${make}' everywhere. This is
wrong for at least the utilities that we may build as companion tools
(make, libtool): this will always invoke the version detected by configure
by supplying the absolute path. In other words, the wrappers in
.build/tools/bin are not fallbacks - they are either temporary (in case
a respective companion tool is built) or permanent redirectors.
This is the reason why the PATH= has .build/*/buildtools/bin at higher
precedence than .build/tools/bin; the latter has the versions detected by
configure and the former has the versions built as companion tools.
Revert the rest of the gang (grep/sed/...) for consistency. After all,
we may decide to supply some of them as well (awk, for instance).
Signed-off-by: Alexey Neyman <stilor@att.net>
|
|
This step was only used in uClibc. However, with upcoming multilib, the
config management will have to be done for each variant differently,
anyway.
uClibc was the only user of libc_check_config step, as well as
CT_CONFIG_DIR directory. Retire these.
Two other clean-ups in uClibc.sh:
- KERNEL_HEADERS check seems to be bogus, this config option is not
present even in 0.9.30 - which is not supported already.
- SHARED_LIB_LOADER_PREFIX was renamed to MULTILIB_DIR in 0.9.31,
according to ChangeLog - and MULTILIB_DIR is passed from command line
instead.
Signed-off-by: Alexey Neyman <stilor@att.net>
|
|
This commit updates the build scripts to match the new usage of
CT_GetCustom from the previous change.
Signed-off-by: Bryan Hundven <bryanhundven@gmail.com>
|
|
We check for apps:
* make
* sed
* grep
* awk
* libtool/libtoolize
* install
* patch
* and more
...during configure. Our scripts should be consistent about using the
variables that define where the found tool was found.
Of course, we do hard-link these tools in buildtools, but that should be
a backup for the components we are building. Our scripts should always
use the tools we find.
Signed-off-by: Bryan Hundven <bryanhundven@gmail.com>
|
|
This commit adds support for the avr-libc C library.
According to the project page at http://www.nongnu.org/avr-libc , the
avr-libc package provides a subset of the standard C library for Atmel
AVR 8-bit RISC microcontrollers. In addition, the library provides the
basic startup code needed by most applications.
Support for this library in crosstool-ng is only enabled for the AVR
8-bit target.
The avr-libc manual and most distributions build the AVR 8-bit gcc
toolchain with the "avr" (non-canonical) target.
Some experimentation also led to the conclusion that other (canonical)
targets are not very well supported, so we force the "avr" target for
crosstool-ng as well.
The manual also recommends building avr-libc after the final gcc build.
To accomplish this with crosstool-ng, a new do_libc_post_cc step is
added, in which currently only avr-libc performs its build, and is a
no-op for the other libc options.
Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
|
Alexey Neyman
Bryan Hundven
Erico Nunes