# Overall toolchain configuration: paths, jobs, etc...

menu "Paths and misc options"

config PARALLEL_JOBS

    int

    prompt "Number of parallel jobs"

    default 1

    help

      Number of jobs make will be allowed to run concurently.

      Set this higher than the number of processors you have, but not too high.

      A good rule of thumb is twice the number of processors you have.

      Enter 1 (or 0) to have only one job at a time.

config LOAD

    int

    prompt "Maximum allowed load"

    default 0

    help

      Specifies that no new jobs should be started if there are others jobs

      running and the load average is at least this value.

      Makes sense on SMP machines only.

      Enter 0 to have no limit on the load average.

      Note: only the integer part of the load is allowed here (you can't enter

            0.75 for example).

config NICE

    int

    prompt "Nice level"

    default 0

    range 0 19

    help

      Renices the build process up.

config USE_PIPES

    bool

    prompt "Use -pipe"

    default y

    help

      Use gcc's option -pipe to use pipes rather than temp files when building

      the toolchain.

comment "Paths"

config TARBALLS_DIR

    string

    prompt "Tarballs directory"

    default "`pwd`/tarballs"

    help

      This is the directory into which tarballs are going to be stored once

      they are downloaded (or otherwise retrieved).

config SRC_DIR

    string

    prompt "Extract directory"

    default "`pwd`/${CT_TARGET}/src"

    help

      This is the directory into which tarballs will be extracted.

      If you will build multiple toolchains, you should arrange to have one

      SRC_DIR for each toolchain, as different targets may require different

      patches to be applied.

config BUILD_DIR

    string

    prompt "Build directory"

    default "`pwd`/${CT_TARGET}/gcc-${CT_CC_VERSION}-${CT_LIBC}-${CT_LIBC_VERSION}"

    help

      This is the directory into which builds will occur.

      Once again, arrange for one build directory for each toolchain you build,

      to avoid collision.

config PREFIX_DIR

    string

    prompt "Prefix directory"

    default "${HOME}/${CT_TARGET}"

    help

      This is the path the toolchain will run from.

config INSTALL_DIR

    string

#    prompt "Install directory"

    default "${CT_PREFIX_DIR}"

#    help

#      This is the path the target will be installed into.

#      

#      Normally, you would set this to ${CT_PREFIX_DIR}, but if for some reasons

#      you can't write there, you can install somewhere else and have a third

#      person do the install for you.

#      The reason you might also want to install elsewhere is if you are going

#      to package your shinny new toolchain for distribution.

config CUSTOM_PATCH

    bool

    prompt "Use custom patch directory"

    default n

    help

      If you have custom patches that you want to be applied, say 'Y' here and

      enter the path directory below.

      Note that you must ensure that the patch directory is arranged the same

      way the official directory is.

config CUSTOM_PATCH_ONLY

    bool

    prompt "Only use custom patches"

    default n

    depends on CUSTOM_PATCH

    help

      Don't apply patches coming with CT-NG, only those patches available in

      the directory below.

      If you say 'N' here, then the patches provided with CT-NG will be applied

      first, and then your patches.

config CUSTOM_PATCH_DIR

    string

    prompt "Custom patch directory"

    default ""

    depends on CUSTOM_PATCH

    help

      Enter the custom patch directory here.

config REMOVE_DOCS

    bool

    prompt "Remove documentation"

    default n

    help

      Remove the installed documentation (man and info pages).

      Gains around 8MiB for a uClibc-based, C and C++ compiler.

comment "Downloading and extracting"

config NO_DOWNLOAD

    bool

    prompt "Avoid downloads"

    default n

    help

      Avoid downloading anything. Bail out if a tarball is missing.

config ONLY_DOWNLOAD

    bool

    prompt "Only download tarballs"

    default n

    depends on ! NO_DOWNLOAD

    help

      Only download the tarballs. Exit once it done.

      Usefull to pre-retrieve the tarballs before going off-line.

config FORCE_DOWNLOAD

    bool

    prompt "Force downloads"

    default n

    depends on ! NO_DOWNLOAD

    help

      Force downloading tarballs, even if one already exists.

      Usefull if you suspect a tarball to be damaged.

config FORCE_EXTRACT

    bool

    prompt "Force extractions"

    depends on ! ONLY_DOWNLOAD

    default n

    help

      Force extraction of already exctracted tarballs.

      Usefull if you suspect a previous extract did not complete (eg. broken

      tarball), or you added a new set of patches for this component.

comment "Logging"

choice

    bool

    prompt "Maximum log level to see:"

    default LOG_INFO

config LOG_ERROR

    bool

    prompt "ERROR"

    help

      The build will be silent.

      Only if there is an error will you see a mesage.

config LOG_WARN

    bool

    prompt "WARN"

    help

      The same as above, plus warnings.

config LOG_INFO

    bool

    prompt "INFO"

    help

      The same as above, plus informational messages (main steps).

config LOG_EXTRA

    bool

    prompt "EXTRA"

    help

      The same as above, plus extra messages (sub-steps).

config LOG_DEBUG

    bool

    prompt "DEBUG"

    help

      The same as above, plus lots of debug information, of which each

      component's build messages (very noisy!).

endchoice

config LOG_LEVEL_MAX

    string

    default "ERROR"   if LOG_ERROR

    default "WARN"    if LOG_WARN

    default "INFO"    if LOG_INFO

    default "EXTRA"   if LOG_EXTRA

    default "DEBUG"   if LOG_DEBUG

config LOG_PROGRESS_BAR

    bool

    prompt "Progress bar"

    default n

    depends on ! LOG_DEBUG

    help

      This option will print a "rotating bar" (/-\|) below the last log line

      to show work is not stalled.

      Available when not in DEBUG log level.

config LOG_USE_COLORS

    bool

    prompt "Use colors for logging to console"

    default n

    help

      Use colors to highlight important messages.

      ERROR: bright red

      WARN : bright yellow

      INFO : bright green

      EXTRA: dim green

      DEBUG: dim white

config LOG_TO_FILE

    bool

    prompt "Log to a file"

    default y

    help

      Save *full* logs to a file. Even log levels you didn't specify above

      will be available in this file.

config LOG_FILE

    string

    prompt "Log file"

    default "${CT_PREFIX_DIR}/${CT_TARGET}.log"

    depends on LOG_TO_FILE

    help

      File name into which to put logs.

endmenu